Table of Content
Then, disconnect the display data cable connector using the same side of the spudger tool as before. Take care to only pry up on the battery connector, and not the socket on the logic board. If you pry up on the logic board socket, you may break the connector entirely.
Use the pointed tip of a spudger to disconnect the home button cable from its connector on the display assembly. Use a spudger or a clean fingernail to disconnect the battery connector by prying it straight up off the logic board. Use a plastic opening tool to hold down the rear case while pulling up the suction cup to open the phone. Use the flat end of a spudger to disconnect the digitizer cable connector. Using the point of the spudger tool, disconnect the home button cable connector by gently pushing it up and away from the home button.
Step 6
Use the flat end of the spudger tool to disconnect the digitizer cable connector. Gently pull the plastic nub on the suction cup to release the vacuum seal and then remove the suction from the display assembly. I will be testing this out myself as soon a I get a new touchID cable/along with the LCD Panel.
If you aren't using the iSclack, skip down three steps for an alternate method. Using a set of tweezers, carefully pull the gasket up and off of the home button carefully so you don’t snag it on the home button cable. You also have to remove the aluminum plate and the rear camera/speaker assembly. After reassembly, connect the iPhone to an AC power source before turning it on for the first time. Once the iPhone has booted up successfully, you can disconnect the AC power.
LCD Display Complete Touch Screen Replacement Button for iPhone 7 6 6s Plus 8
You may need to transfer remaining components before installing. Wear safety glasses to protect your eyes from any glass shaken free during the repair. Lay overlapping strips of clear packing tape over the iPhone's display until the whole face is covered. Choose a size and copy the code below to embed this guide as a small widget on your site / forum.
The rubber gasket surrounding the home button is very thin and tears easily. Carefully wedge the tip of a spudger underneath the home button connector cable. Be sure the cup is pressed securely onto the screen to get a tight seal. Close the handle on the iSclack, opening the suction cup jaws. If the plastic depth gauge is attached at the center of the iSclack, remove it now—it's not needed for larger phones like the iPhone 6 Plus.
Screen
Use a spudger or a fingernail to disconnect the home button cable connector. As technology advances, there’s still room for dreadful technical malfunctions like, error 53. This common error occurs when replacing a broken home button’s Touch ID on the iPhone 6/6 Plus with an unoriginal part from another phone, or a damaged flex cable. To fix this annoying error, replacing a basic accessory i-e USB cable is a quick and inexpensive fix.
We also offer a mail-in repair service for customers who can’t get to a local store. If paying $200.00 is not in your budget to repair your broken home button, shopping for the best price is going to save you time, money, and headaches. Some services like iFixandRepair are charging $70.00, and Genius Phone Repair is quoted at $104.99 to fix an iPhone 6/6 Plus home button. To reassemble your iPhone 6/6 Plus, simply follow these instructions in reverse order and you have officially fixed your iPhone’s broken home button. Gently peel back the home button the rest of the way off of the display with the spudger tool. Power off your iPhone 6/6 Plus and remove the two 3.6 mm pentalobe screws next to the lighting connector or where you commonly plug your phone in.
iPhone 5s / SE Genuine Ear Speaker
Be careful not to snag the gasket on the home button cable. I use ifixits metal spudger without heat but one small mistake and it can be teared. Do not push the home button all the way through—you only need to get a corner free so that you can pry it free with a spudger. Apply mild heat to soften the adhesive securing the home button membrane. During your repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your phone. Open the iPhone by swinging the home button end of the front panel assembly away from the rear case, using the top of the phone as a hinge.
Remove the two 3.6 mm P2 Pentalobe screws next to the Lightning connector.
A passive matrix has a grid of conductors with pixels at each intersection and a current travels along two conductors on the grid to control the pixel light. An active matrix display has more refresh time with clearer and crisper technology. The final charge may be different depending on the delivery address.
Unique assembly kits do not exist for each particular phone generation. Follow the steps in this guide to replace the Home Button Assembly, including the gasket and cable, in your iPhone 6s Plus. Note that home buttons are paired with their respective logic board, so Touch ID will no longer work after you replace the Home Button Assembly. Use the point of a spudger to disconnect the home button cable connector by pushing it up and away from the home button.
If you’re within your one-year Apple Care warranty, Apple will charge you $79.00 to repair your broken home button. If your Apple Care warranty has expired, expect to pay approximately $200.00 for all iPhone 6/6 Plus home button repairs. Using the top of the phone as a hinge, pull the home button end of the front panel away from the rear case. Release the power button and then press and hold the home button until the, “slide to power off” slider vanishes. Repeatedly slamming your finger into a broken, sticky, or burning hot iPhone 6/6 Plus home button won’t magically fix your crippled device.
Its a good advice to remove the battery power before mounting the flex-cables. Use the point of a spudger to carefully separate the home button cable from the adhesive securing it to the front panel. Peel the home button the rest of the way off of the display by prying gently with a spudger. Position the iSclack's upper suction cup against the display, just above the home button. The next three steps demonstrate using the iSclack, a great tool for safely opening the iPhone 6 that we recommend for anyone doing more than one repair.
Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen. Don't open the display more than 90º—it is still connected to the top of the phone by the display, digitizer, and front camera cables which can tear easily. Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.
No comments:
Post a Comment